-- *****************************************************************
-- ALPS-MIB.my: Airline Protocol Support MIB
--
-- October 1997, Shantanu Sarkar & Mohan Tadisetty
--
-- Copyright (c) 1997-1999, 2000, 2008 by cisco Systems Inc.
-- *****************************************************************CISCO-ALPS-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Counter32,Gauge32,Integer32,IpAddress,TimeTicks,NOTIFICATION-TYPEFROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUPFROM SNMPv2-CONF
DisplayString,TEXTUAL-CONVENTION,TruthValue,RowStatus,TimeStamp,TimeIntervalFROM SNMPv2-TC
ifIndex,InterfaceIndexFROM IF-MIB
ciscoMgmt
FROM CISCO-SMI
X121AddressFROM RFC1382-MIB;ciscoAlpsMIB MODULE-IDENTITYLAST-UPDATED"200802140000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 W. Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-alps@cisco.com"DESCRIPTION"The MIB module for Airline Protocol Support.
**************************************************************
* Acronym Definitions *
* *
* ALPS : AirLine Protocol Support *
* AX.25 : Airline X.25 *
* EMTOX : Exchange of Mixed Traffic over X.25 *
* ASCU : Agent Set Control Unit *
* *
**************************************************************
Overview of ALPS (AirLine Protocol Support) MIB
==============================================
MIB description
Document to refer: 'Configuring ALPS' section in Cisco IOS Command
Reference & Configuration Guide.
The ALPS MIB provides configuration and operational information
for Cisco's Airline protocol support for IBM-P1024B(ALC) and
Unisys-P1024C(UTS) protocols encapsulation over TCP/IP. The
following entities are managed:
1. Peers
2. ALPS Circuits
3. ASCUs (Agent Set Control Units)
4. ALC interface
5. ALPS Host link interface to the host
HOST(Emtox/Ax.25) <----> Central <---> IP Network <---> Remote <----> ASCU
router router
The router connected to the Host is called the Central router and the router
connected to the ASCU is called the Remote router. We anticipate one Central
router connecting to a large number of Remote routers. Each router has a
local peer, which connects to its counterpart on the other router (referred
to as the remote peer) via a TCP connection. ALPS circuits are set up over
this TCP connection either on a permanent or on-demand basis.
A logical grouping of ASCUs are connected via a single circuit - this has
no connection to the physical interfaces that the ASCUs are connected to.
The only restriction is that all the ASCUs should be directly connected to
the same router.
Multiple ASCUs can connect to a single serial interface and several terminals
connect to an ASCU. However, terminals are not visible to the ALPS feature
- the router talks only to the ASCUs. An ASCU can be identified by
* the interface it is on and its Interface Address (IA) or
* the circuit it is on, and its A1 and A2 values, which identify it
within the circuit.
Thus there are two ways of identifying an ASCU - or
Circuit names are globally unique.
The connection to the host is via one of two flavors of X.25 - either
AX.25 (for PVCs) or EMTOX (for SVCs). Each X.25 VC corresponds to one ALPS
circuit. There are several hostlinks between a host and the Central router
and load balancing is done across these. EMTOX allows the host to
dial out to a terminal. This requires the use of an X.121 to IP address
translation table to connect to the appropriate remote peer."REVISION"200802140000Z"DESCRIPTION"Imported X121Adress from RFC1382 MIB & Integer32 from
SNMPv2-SMI. TEXTUAL-CONVENTION AlpsCktName syntax is changed
to OCTET STRING from DisplayString & AlpsAscuA1A2Value's Syntax
is changed to Integer32 from INTEGER. Syntax of following objects
are changed from INTEGER to Integer32:
alpsPeerLocalAtpPort, alpsPeerKeepaliveMaxRetries,
alpsRemPeerLocalPort, alpsRemPeerRemotePort, alpsRemPeerTCPQlen,
alpsRemPeerCfgTCPQLen, alpsRemPeerCfgStatRetry,
alpsRemPeerConnLocalPort, alpsRemPeerConnForeignPort,
alpsRemPeerConnNumActCirc, alpsRemPeerConnTCPQLen,
alpsRemPeerConnStatIntvl, alpsRemPeerConnStatRetry,
alpsCktBaseNumActiveAscus, alpsCktBaseHostLinkNumber,
alpsCktBaseRemHld, alpsCktBaseLocalHld, alpsCktX25LCN,
alpsCktP1024Ax25LCN, alpsCktP1024WinOut, alpsCktP1024WinIn,
alpsCktP1024OutPktSize, alpsCktP1024InPktSize,
alpsCktP1024SvcMsgList, alpsCktAscuId, alpsIfP1024MaxErrCnt,
alpsIfP1024MaxRetrans, alpsIfP1024CurrErrCnt,
alpsIfP1024MinGoodPollResp, alpsIfP1024PollingRatio,
alpsIfHLinkHostHld, alpsIfHLinkNumber, alpsIfHLinkActiveCkts,
alpsAscuId, alpsAscuMaxMsgLength, alpsSvcMsgListNum and
alpsSvcMsgNum."REVISION"200001280000Z"DESCRIPTION"Modification for ALC and Service Message Enhancements"REVISION"9901070000Z"DESCRIPTION"Additional modifications to support ALPS/MATIP.
NOTE: The alpsIfHLinkHostHld object has been updated to
change its range. SMI (RFC2578 section 10.2 Extending an
Information Module: Object Definitons) requires a new object
defined and the old object obsoleted. This is also an
index module which would require the old table to be
obsoleted and a new one created. After review it has been
decided to minimize impacts/disruptions to customer
applications, we are not going to follow the SMI guidlines."REVISION"9812310000Z"DESCRIPTION"Modifications to support ALPS/MATIP."REVISION"9812080000Z"DESCRIPTION"Modifications to allow publishing."REVISION"9805200000Z"DESCRIPTION"Change ranges for some variables and update descriptions."::={ ciscoMgmt 95}-- 0 to 17 bytes in length containing the ASCII
-- characters [0-9], each octet contains one digit
-- of the address.
--
-- /***************************************/
-- The OBJECT IDENTIFIERS FOR ALPS MIBS
-- /***************************************/ciscoAlpsMIBObjects OBJECTIDENTIFIER::={ ciscoAlpsMIB 1}-- /***************************************/
-- The Global Object Declarations
-- /***************************************/AlpsCktName ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Specifies the ALPS Circuit Name. It is configured from the
parser and is adminstratively assigned. This is globally unique."SYNTAXOCTETSTRING(SIZE(1..12))AlpsAscuA1A2Value ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Specifies A1 or A2 value of an ASCU. The A1 & A2 values
together specify an ASCU within an ALPS circuit."SYNTAXInteger32(0..255)-- *********************************************************************
-- * Define ALPS Local Peer
-- *********************************************************************alpsGroups OBJECTIDENTIFIER::={ ciscoAlpsMIBObjects 1}alpsPeerObjects OBJECTIDENTIFIER::={ ciscoAlpsMIBObjects 2}alpsCktObjects OBJECTIDENTIFIER::={ ciscoAlpsMIBObjects 3}alpsIfObjects OBJECTIDENTIFIER::={ ciscoAlpsMIBObjects 4}alpsAscuObjects OBJECTIDENTIFIER::={ ciscoAlpsMIBObjects 5}alpsGlobalObjects OBJECTIDENTIFIER
::={ ciscoAlpsMIBObjects 6}-- These MIB objects configure the local ALPS peer. The local peer
-- connects to remote ALPS peers using a TCP/IP tunnel and sets
-- up ALPS circuits across the tunnel.alpsPeer OBJECTIDENTIFIER::={ alpsPeerObjects 1}alpsPeerLocalIpAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The configured IP address used by the ALPS component in
this router."::={ alpsPeer 1}alpsPeerLocalAtpPort OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The port number used locally by the ALPS peer at this router.
This is a static value but the port number used can change in
later versions. This is not a configured value but is embedded
into the source code. This has been provided mainly to aid
in debugging so that the operator knows which TCP port to
look at. ATP is the ALPS Tunnelling Protocol, a Cisco proprietary
way to tunnel ALPS data across a TCP link"::={ alpsPeer 2}alpsPeerKeepaliveTimeout OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The TCP keep alive timeout value for Local ALPS Peer. Keepalives
are sent out periodically at this interval to the remote peer."::={ alpsPeer 3}alpsPeerKeepaliveMaxRetries OBJECT-TYPESYNTAXInteger32(0..10)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The number of keepalives sent with acknowledgement before declaring
the remote peer dead. 0 implies that keepalives are turned off."::={ alpsPeer 4}alpsPeerInCallsAcceptFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"If this is true, calls are accepted from any peer. If this is
false, calls are accepted only from those routers which have
been explicitly configured using alps remote-peer commands."DEFVAL{ false }::={ alpsPeer 5}-- *********************************************************************
-- Deprecated ALPS Remote Peer table
-- *********************************************************************alpsRemPeerTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsRemPeerEntry
MAX-ACCESSnot-accessibleSTATUSdeprecatedDESCRIPTION"A list of Remote peers that the local ALPS peer can communicate
with."::={ alpsPeerObjects 2}
alpsRemPeerEntry OBJECT-TYPESYNTAX AlpsRemPeerEntry
MAX-ACCESSnot-accessibleSTATUSdeprecatedDESCRIPTION"Each entry represents an Remote ALPS Peer."INDEX{ alpsRemPeerIpAddr }::={ alpsRemPeerTable 1}
AlpsRemPeerEntry ::=SEQUENCE{
alpsRemPeerIpAddr IpAddress,
alpsRemPeerConnType INTEGER,
alpsRemPeerLocalPort Integer32,
alpsRemPeerRemotePort Integer32,
alpsRemPeerState INTEGER,
alpsRemPeerUptime TimeTicks,
alpsRemPeerNumActiveCkts Gauge32,
alpsRemPeerIdleTimer TimeInterval,
alpsRemPeerAlarmsEnabled TruthValue,
alpsRemPeerTCPQlen Integer32,
alpsRemPeerOutPackets Counter32,
alpsRemPeerOutOctets Counter32,
alpsRemPeerInPackets Counter32,
alpsRemPeerInOctets Counter32,
alpsRemPeerDropsGiant Counter32,
alpsRemPeerDropsQFull Counter32,
alpsRemPeerDropsPeerUnreach Counter32,
alpsRemPeerRowStatus RowStatus}alpsRemPeerIpAddr OBJECT-TYPESYNTAXIpAddress
MAX-ACCESSnot-accessibleSTATUSdeprecatedDESCRIPTION"The remote IP address for the TCP Connection."::={ alpsRemPeerEntry 1}alpsRemPeerConnType OBJECT-TYPESYNTAXINTEGER{permanent(1),dynamic(2)}MAX-ACCESSread-createSTATUSdeprecatedDESCRIPTION"Type of ALPS circuit established. Dynamic circuits are
established only when there is data traffic that needs to be
sent across and are closed when the alpsRemPeerIdleTimer
expires. Permanent circuits stay up regardless of whether
there is traffic across them or not."::={ alpsRemPeerEntry 2}alpsRemPeerLocalPort OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The port number used locally by the tcp connection for the
circuit. the initiator of a connection will dynamically assign
a port number. the other end of the connection will have a
well-known port number applicable to the encapsulation used by
the connection - e.g. the value of alpsPeerLocalAtpPort for
ATP connections."::={ alpsRemPeerEntry 3}alpsRemPeerRemotePort OBJECT-TYPE
SYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The port number used by the remote end of the tcp connection
for the circuit. the initiator of a connection will
dynamically assign a port number. the other end of the
connection will have a well-known port number applicable to
the encapsulation used by the connection - e.g. the value of
alpsPeerLocalAtpPort for ATP connections.
If this connection was initiated by the local router,
a port number will be dynamically selected. Otherwise the value of
alpsPeerLocalAtpPort will be used (for ATP connections)"::={ alpsRemPeerEntry 4}alpsRemPeerState OBJECT-TYPESYNTAXINTEGER{closed(1),opening(2),opened(3)}MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"TCP Peer State. Initially the connection is in the closed state.
For permanent connections, it starts opening the TCP connection
immediately, but for dynamic ones, it waits till there is traffic
addressed to the remote peer. It then progresses via opening into
the opened state."::={ alpsRemPeerEntry 5}alpsRemPeerUptime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUSdeprecated
DESCRIPTION"Time elapsed since TCP connection was established."::={ alpsRemPeerEntry 6}alpsRemPeerNumActiveCkts OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of active ALPS circuits in this TCP session."::={ alpsRemPeerEntry 7}alpsRemPeerIdleTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUSdeprecatedDESCRIPTION"The TCP session with the peer will be closed if there is no
activity for alpsInactiveTimer seconds. This is valid only
for dynamic circuits"::={ alpsRemPeerEntry 8}alpsRemPeerAlarmsEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUSdeprecatedDESCRIPTION"Specifies whether alarms are generated for this remote Peer"DEFVAL{ false }::={ alpsRemPeerEntry 9}alpsRemPeerTCPQlen OBJECT-TYPESYNTAXInteger32(1..200)UNITS"packets"MAX-ACCESSread-create
STATUSdeprecatedDESCRIPTION"Maximum TCP Queue size allowed for this TCP session."::={ alpsRemPeerEntry 10}alpsRemPeerOutPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of packets transmitted to the remote peer."::={ alpsRemPeerEntry 11}alpsRemPeerOutOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of octets transmitted to the remote peer."::={ alpsRemPeerEntry 12}alpsRemPeerInPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of packets received from the remote peer."::={ alpsRemPeerEntry 13}alpsRemPeerInOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUSdeprecated
DESCRIPTION"Number of octets received from the remote peer."::={ alpsRemPeerEntry 14}alpsRemPeerDropsGiant OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of Packets dropped because they were larger than the
maximum allowed packet size of 3840 bytes."::={ alpsRemPeerEntry 15}alpsRemPeerDropsQFull OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of packets dropped because the TCP queue (of
size alpsRemPeerTCPQlen) was full."::={ alpsRemPeerEntry 16}alpsRemPeerDropsPeerUnreach OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"Number of packets dropped because remote peer was unreachable."::={ alpsRemPeerEntry 17}alpsRemPeerRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUSdeprecated
DESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsRemPeerEntry 18}-- *******************************************************************
-- Define ALPS Remote Peer Tables.
--
-- The ALPS Remote Peer Tables are now split into two tables,
-- one table for ALPS remote peer configurations and a second
-- table for ALPS remote peer connections. The table for ALPS
-- remote peer connections contains the objects that manage
-- the TCP connections used by ALPS. The table for ALPS
-- remote peer configuration objects contains the information
-- that objects in the remote peer connection table use to
-- configure themselves. The alpsRemPeerTable was deprecated
-- and split into these 2 tables because ALPS/MATIP peer connections
-- do not have a 1-to-1 mapping to an ALPS remote peer configuration
-- object. Several ALPS/MATIP peer connections can use the same ALPS
-- remote peer configuration, provided the ALPS/MATIP peer connections
-- share the same remote peer IP address.
-- *******************************************************************
--
-- ***************************************
-- ALPS Remote Peer Configuration Table
-- ***************************************alpsRemPeerCfgTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsRemPeerCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing of all administered ALPS remote peer
configuration entries on this node. Entries in
this table can be created via a CLI command or via
alpsRemPeerCfgRowStatus."::={ alpsPeerObjects 3}alpsRemPeerCfgEntry OBJECT-TYPESYNTAX AlpsRemPeerCfgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents an ALPS remote peer
configuration entry on this node."
INDEX{
alpsRemPeerCfgIpAddr,
alpsRemPeerCfgProtocol
}::={ alpsRemPeerCfgTable 1}
AlpsRemPeerCfgEntry ::=SEQUENCE{
alpsRemPeerCfgIpAddr IpAddress,
alpsRemPeerCfgProtocol INTEGER,
alpsRemPeerCfgActivation INTEGER,
alpsRemPeerCfgTCPQLen Integer32,
alpsRemPeerCfgIdleTimer TimeInterval,
alpsRemPeerCfgNoCircTimer TimeInterval,
alpsRemPeerCfgAlarmsOn TruthValue,
alpsRemPeerCfgStatIntvl TimeInterval,
alpsRemPeerCfgStatRetry Integer32,
alpsRemPeerCfgRowStatus RowStatus}alpsRemPeerCfgIpAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The configured IP address of an ALPS remote peer."::={ alpsRemPeerCfgEntry 1}alpsRemPeerCfgProtocol OBJECT-TYPESYNTAXINTEGER{atp(1),matipTypeA(2)}MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"The configured ALPS protocol encapsulation. This
protocol encapsulation is at the layer above TCP."::={ alpsRemPeerCfgEntry 2}alpsRemPeerCfgActivation OBJECT-TYPESYNTAXINTEGER{permanent(1),dynamic(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured type of ALPS peer activation."::={ alpsRemPeerCfgEntry 3}alpsRemPeerCfgTCPQLen OBJECT-TYPESYNTAXInteger32(1..100)UNITS"packets"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured maximum TCP Queue size."::={ alpsRemPeerCfgEntry 4}alpsRemPeerCfgIdleTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured idle timer for a dynamic
activation peer."::={ alpsRemPeerCfgEntry 5}alpsRemPeerCfgNoCircTimer OBJECT-TYPESYNTAXTimeInterval
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured no-circuit timer for a dynamic
activation peer."::={ alpsRemPeerCfgEntry 6}alpsRemPeerCfgAlarmsOn OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured parameter which specifies whether
alarms are generated for remote peer connections
to the IP address in alpsRemPeerCfgIpAddr."DEFVAL{ false }::={ alpsRemPeerCfgEntry 7}alpsRemPeerCfgStatIntvl OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured status interval timer."::={ alpsRemPeerCfgEntry 8}alpsRemPeerCfgStatRetry OBJECT-TYPESYNTAXInteger32(0..100)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The configured number of status retries."::={ alpsRemPeerCfgEntry 9}alpsRemPeerCfgRowStatus OBJECT-TYPESYNTAXRowStatus
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsRemPeerCfgEntry 10}-- ***************************************
-- ALPS Remote Peer Connection Table
-- ***************************************alpsRemPeerConnTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsRemPeerConnEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table listing of all ALPS remote peer
connections on this node."::={ alpsPeerObjects 4}alpsRemPeerConnEntry OBJECT-TYPESYNTAX AlpsRemPeerConnEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry represents an ALPS remote peer
connection on this node."INDEX{
alpsRemPeerConnIpAddr,
alpsRemPeerConnIdString
}::={ alpsRemPeerConnTable 1}
AlpsRemPeerConnEntry ::=SEQUENCE{
alpsRemPeerConnIpAddr IpAddress,
alpsRemPeerConnIdString DisplayString,
alpsRemPeerConnLocalPort Integer32,
alpsRemPeerConnForeignPort Integer32,
alpsRemPeerConnState INTEGER,
alpsRemPeerConnProtocol INTEGER,
alpsRemPeerConnCreation INTEGER,
alpsRemPeerConnActivation INTEGER,
alpsRemPeerConnUptime TimeTicks,
alpsRemPeerConnNumActCirc Integer32,
alpsRemPeerConnLastTxRx TimeStamp,
alpsRemPeerConnLastRxAny TimeStamp,
alpsRemPeerConnIdleTimer TimeInterval,
alpsRemPeerConnNoCircTimer TimeInterval,
alpsRemPeerConnTCPQLen Integer32,
alpsRemPeerConnAlarmsOn TruthValue,
alpsRemPeerConnStatIntvl Integer32,
alpsRemPeerConnStatRetry Integer32,
alpsRemPeerConnDownReason INTEGER,
alpsRemPeerConnOutPackets Counter32,
alpsRemPeerConnOutOctets Counter32,
alpsRemPeerConnInPackets Counter32,
alpsRemPeerConnInOctets Counter32,
alpsRemPeerConnDropsGiant Counter32,
alpsRemPeerConnDropsQFull Counter32,
alpsRemPeerConnDropsUnreach Counter32,
alpsRemPeerConnDropsVersion Counter32}alpsRemPeerConnIpAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The IP address of the ALPS remote peer."::={ alpsRemPeerConnEntry 1}
alpsRemPeerConnIdString OBJECT-TYPESYNTAXDisplayString(SIZE(1..20))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A descriptive ASCII string that is used to distinguish
among different peer connections to the same ALPS remote
peer IP address."::={ alpsRemPeerConnEntry 2}alpsRemPeerConnLocalPort OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local TCP port number used by the underlying
TCP connection to an ALPS remote peer."::={ alpsRemPeerConnEntry 3}alpsRemPeerConnForeignPort OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The foreign (remote) TCP port number used by the
underlying TCP connection to an ALPS remote peer."::={ alpsRemPeerConnEntry 4}alpsRemPeerConnState OBJECT-TYPESYNTAXINTEGER{closed(1),
opening(2),opened(3),busy(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The state of the connection to an ALPS remote peer."::={ alpsRemPeerConnEntry 5}alpsRemPeerConnProtocol OBJECT-TYPESYNTAXINTEGER{atp(1),matipTypeA(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The ALPS protocol encapsulation used on the
connection to the ALPS remote peer. This protocol
encapsulation is a layer above TCP."::={ alpsRemPeerConnEntry 6}alpsRemPeerConnCreation OBJECT-TYPESYNTAXINTEGER{admin(1),learned(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The stimulus for creating the peer connection object.
The peer connection object may be created solely due to
configuration (admin) or due to a combination of
configuration and protocol events (learned)."::={ alpsRemPeerConnEntry 7}alpsRemPeerConnActivation OBJECT-TYPESYNTAXINTEGER{permanent(1),dynamic(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Basis for activation a peer connection. A permanent activation peer
connection will attempt to open immediately and stay open, regardless
of the usage of the peer connection. A dynamic activation peer
connection only opens when there is data to send and the peer connection
will close if there are no data messages sent or received across the peer
for the duration of the idle timer."::={ alpsRemPeerConnEntry 8}alpsRemPeerConnUptime OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Elapsed time since the ALPS peer connection
was successfully established."::={ alpsRemPeerConnEntry 9}alpsRemPeerConnNumActCirc OBJECT-TYPESYNTAXInteger32(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The number of ALPS virtual circuits using the
connection to this ALPS remote peer."::={ alpsRemPeerConnEntry 10}alpsRemPeerConnLastTxRx OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of sysUpTime when a peer data message
was last transmitted or received across this
ALPS remote peer connection. This timestamp is not
update if the peer message is a peer status
inquiry/response message."::={ alpsRemPeerConnEntry 11}alpsRemPeerConnLastRxAny OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of sysUpTime when a peer data or
status message is last received across the
ALPS remote peer connection."::={ alpsRemPeerConnEntry 12}alpsRemPeerConnIdleTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A dynamic activation ALPS peer connection will be closed
if zero peer data messages are sent or received for
a length of time greater than or equal to this timer."::={ alpsRemPeerConnEntry 13}alpsRemPeerConnNoCircTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"A dynamic activation ALPS peer connection will be closed
if zero ALPS circuits are active or attempt to activate
for a length of time greater than or equal to this timer."::={ alpsRemPeerConnEntry 14}alpsRemPeerConnTCPQLen OBJECT-TYPESYNTAXInteger32(1..100)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The maximum number of ALPS peer messages that
can be queued in a single TCP session."::={ alpsRemPeerConnEntry 15}alpsRemPeerConnAlarmsOn OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This parameter specifies whether ALPS alarms
are generated for this ALPS remote peer connection."::={ alpsRemPeerConnEntry 16}alpsRemPeerConnStatIntvl OBJECT-TYPESYNTAXInteger32(0..300)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The time interval (in seconds) between transmission of
consecutive ALPS Peer Status messages. These messages
are only transmitted if zero messages are received on the
peer connection for a length of time greater than or equal
to this timer."::={ alpsRemPeerConnEntry 17}
alpsRemPeerConnStatRetry OBJECT-TYPESYNTAXInteger32(0..100)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of consecutive unanswered ALPS Peer Status
messages transmitted before closing the conenction to
the ALPS remote peer."::={ alpsRemPeerConnEntry 18}alpsRemPeerConnDownReason OBJECT-TYPESYNTAXINTEGER{unknown(1),idle(2),noCircuits(3),destUnreachable(4),foreignReset(5),localReset(6),noMemory(7),openingTimeout(8)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reason that an ALPS Peer connection failed to
open sauccessfully."::={ alpsRemPeerConnEntry 19}alpsRemPeerConnOutPackets OBJECT-TYPE
SYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets transmitted on this ALPS
remote peer connection."::={ alpsRemPeerConnEntry 20}alpsRemPeerConnOutOctets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of octets transmitted on this ALPS
remote peer connection."::={ alpsRemPeerConnEntry 21}alpsRemPeerConnInPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets received on this ALPS
remote peer connection."::={ alpsRemPeerConnEntry 22}alpsRemPeerConnInOctets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of octets received on this ALPS
remote peer connection."::={ alpsRemPeerConnEntry 23}alpsRemPeerConnDropsGiant OBJECT-TYPE
SYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of ALPS peer packets dropped due to exceeding
the maximum allowed packet size of 3840 bytes."::={ alpsRemPeerConnEntry 24}alpsRemPeerConnDropsQFull OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of ALPS peer packets dropped because
the TCP output queue is full."::={ alpsRemPeerConnEntry 25}alpsRemPeerConnDropsUnreach OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of ALPS peer packets dropped because
the ALPS remote peer is unreachable."::={ alpsRemPeerConnEntry 26}alpsRemPeerConnDropsVersion OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of ALPS peer packets dropped because
of a version mismatch in the ALPS encapsulation."::={ alpsRemPeerConnEntry 27}
-- *********************************************************************
-- Define ALPS Circuit tables - these are also organised into a base
-- table and a dlc-type specific table (X25 or P1024)
-- Similar to the Peer tables, these would contain configured circuits at
-- the remote router and entries for dynamically created circuits at the
-- Central router
-- *********************************************************************alpsCktBaseTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsCktBaseEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of ALPS circuits. This table contains variables
common to central & remote routers."::={ alpsCktObjects 1}alpsCktBaseEntry OBJECT-TYPESYNTAX AlpsCktBaseEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details of ALPS Circuits."INDEX{
alpsCktBaseName,
alpsCktBaseDlcType
}::={ alpsCktBaseTable 1}
AlpsCktBaseEntry ::=SEQUENCE{
alpsCktBaseName AlpsCktName,
alpsCktBaseDlcType INTEGER,
alpsCktBasePriPeerAddr IpAddress,
alpsCktBaseAlarmsEnabled TruthValue,
alpsCktBaseConnType INTEGER,
alpsCktBaseState INTEGER,
alpsCktBaseNumActiveAscus Integer32,
alpsCktBaseCurrentPeer IpAddress,
alpsCktBaseLifeTimeTimer TimeInterval,
alpsCktBaseHostLinkNumber Integer32,
alpsCktBaseHostLinkType INTEGER,
alpsCktBaseRemHld Integer32,
alpsCktBaseLocalHld Integer32,
alpsCktBaseDownReason INTEGER,
alpsCktBaseOutPackets Counter32,
alpsCktBaseOutOctets Counter32,
alpsCktBaseInPackets Counter32,
alpsCktBaseInOctets Counter32,
alpsCktBaseDropsCktDisabled Counter32,
alpsCktBaseDropsQOverflow Counter32,
alpsCktBaseDropsLifeTimeExpd Counter32,
alpsCktBaseEnabled TruthValue,
alpsCktBaseRowStatus RowStatus,
alpsCktBaseCurrPeerConnId DisplayString}alpsCktBaseName OBJECT-TYPESYNTAX AlpsCktName
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the ALPS Circuit Name. This is unique within the
network."::={ alpsCktBaseEntry 1}alpsCktBaseDlcType OBJECT-TYPESYNTAXINTEGER{emtox(1),ax25(2),
alc(3),uts(4)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies what type of circuit this is. The X25 circuit is set up
with the same name as the P1024 circuit so we need this
variable to distinguish between the two, in case local switching
is done."::={ alpsCktBaseEntry 2}alpsCktBasePriPeerAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This is the IP address of the Primary Central peer. It is
mandatory to configure a primary peer, but the backup peer is
optional."::={ alpsCktBaseEntry 3}alpsCktBaseAlarmsEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies whether alarms are generated for this ALPS circuit.
Alarms can be syslog messages or SNMP traps - both are controlled
using the same flags."DEFVAL{ false }::={ alpsCktBaseEntry 4}alpsCktBaseConnType OBJECT-TYPESYNTAXINTEGER{permanent(1),
dynamic(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the ALPS Circuit Connection Type."::={ alpsCktBaseEntry 5}alpsCktBaseState OBJECT-TYPESYNTAXINTEGER{disabled(1),inoperable(2),opening(3),opened(4),cktBusy(5),peerBusy(6),updating(7)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the state of ALPS Circuit."::={ alpsCktBaseEntry 6}alpsCktBaseNumActiveAscus OBJECT-TYPESYNTAXInteger32(0..64)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the number of enabled ASCUs that are attached to
this ALPS Circuit. Attachment of an ASCU to an ALPS circuit
may occur due to configuration or due to information passed
in a protocol message."::={ alpsCktBaseEntry 7}alpsCktBaseCurrentPeer OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the IP address of the peer that this ALPS circuit
is currently connected to."::={ alpsCktBaseEntry 8}alpsCktBaseLifeTimeTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUScurrentDESCRIPTION"A data message that has been queued within the router for
longer than this interval will be dropped."::={ alpsCktBaseEntry 9}alpsCktBaseHostLinkNumber OBJECT-TYPESYNTAXInteger32(1..255)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies host link number (on Central router) for this ALPS
Circuit. The host link number is used to provide a
degree of transparency to the remote router. A single host link
may correspond to multiple physical links between the central
router and the host, which can then load-balance VCs across
them."::={ alpsCktBaseEntry 10}alpsCktBaseHostLinkType OBJECT-TYPE
SYNTAXINTEGER{ax25(1),emtox(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies host link type(on Central router) for this
ALPS Circuit."::={ alpsCktBaseEntry 11}alpsCktBaseRemHld OBJECT-TYPESYNTAXInteger32(1..32639)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the HLD (High-level descriptor) of the AX.25/EMTOX
host for this ALPS Circuit. This serves as an identifier
for the host"::={ alpsCktBaseEntry 12}alpsCktBaseLocalHld OBJECT-TYPESYNTAXInteger32(1..32639)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the local HLD for this ALPS Circuit. HLDs are required
at the host for both ends of the connection."::={ alpsCktBaseEntry 13}alpsCktBaseDownReason OBJECT-TYPESYNTAXINTEGER{unknown(1),
noReason(2),hostLinkDown(3),cktDisabled(4),hostLinkDisabled(5),noHostLinkMatched(6),noHldMatched(7),cktNameInUse(8),pvcLcnOutOfRange(9),x25ParamInvalid(10),cktOpeningTimeout(11),x25ClearDteNoReason(12),configMismatch(13),noResourcesAvail(14),incompatibleA1A2(15),cktIdle(16),peerDown(17),noAscusConfigured(18),x25ClearHostUnknown(19),x25ClearHostDown(20),x25ClearHostDisabled(21),
x25ClearHostSaturated(22),x25ClearCallerUnknown(23),x25ClearCallerUnauth(24),x25ClearConfigRejected(25),x25ClearConfigFallback(26),x25ClearConfigIncompat(27),x25ClearHLDUnknown(28),x25ClearPIDUnknown(29),x25ClearFacilRejected(30),x25ClearNetNoReason(31),pvcLcnInUse(32),noSvcLcnAvail(33),peerIdle(34),presUnknown(35),presMismatch(36),openMsgTooShort(37),mpxUnknown(38),mpxHdrMismatch(39),trafTypeMismatch(40),
codingMismatch(41),ascuInSession(42)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the reason why this ALPS Circuit is down, if it is down."DEFVAL{ noReason }::={ alpsCktBaseEntry 14}alpsCktBaseOutPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets transmitted to remote peer over this circuit."::={ alpsCktBaseEntry 15}alpsCktBaseOutOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of octets transmitted to remote peer over this circuit."::={ alpsCktBaseEntry 16}alpsCktBaseInPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets received from remote peer over this circuit."::={ alpsCktBaseEntry 17}alpsCktBaseInOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of octets received from remote peer over this circuit."::={ alpsCktBaseEntry 18}alpsCktBaseDropsCktDisabled OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets dropped because the circuit was disabled. This
would typically be packets that were queueued before the circuit was
disabled which are now left in the queue."::={ alpsCktBaseEntry 19}alpsCktBaseDropsQOverflow OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets dropped due to TCP Congestion."::={ alpsCktBaseEntry 20}alpsCktBaseDropsLifeTimeExpd OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Number of packets which were queued within the router for
longer than alpsCktBaseLifeTimeTimer."::={ alpsCktBaseEntry 21}alpsCktBaseEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This specifies if the circuit has been enabled. After a circuit
has been configured, it must be explicitly enabled in order for
the circuit to be set up."DEFVAL{ false }::={ alpsCktBaseEntry 22}alpsCktBaseRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsCktBaseEntry 23}alpsCktBaseCurrPeerConnId OBJECT-TYPESYNTAXDisplayString(SIZE(1..20))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A descriptive ASCII string that is used to distinguish
among different peer connections to the same ALPS remote
peer IP address."::={ alpsCktBaseEntry 24}-- X.25 ckt TablealpsCktX25Table OBJECT-TYPE
SYNTAXSEQUENCEOF AlpsCktX25Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of ALPS X.25 circuits. These entries exist only for X.25
circuits. hence this table would probably be empty at the remote
router"::={ alpsCktObjects 2}alpsCktX25Entry OBJECT-TYPESYNTAX AlpsCktX25Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details of ALPS Circuits."INDEX{
alpsCktBaseName,
alpsCktX25DlcType
}::={ alpsCktX25Table 1}
AlpsCktX25Entry ::=SEQUENCE{
alpsCktX25DlcType INTEGER,
alpsCktX25IfIndex InterfaceIndex,
alpsCktX25LCN Integer32,
alpsCktX25HostX121 X121Address,
alpsCktX25RemoteX121 X121Address,
alpsCktX25DropsVcReset Counter32}alpsCktX25DlcType OBJECT-TYPESYNTAXINTEGER{emtox(1),ax25(2)}MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"Specifies what type of circuit this is."::={ alpsCktX25Entry 1}alpsCktX25IfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the interface the circuit is on. This is the interface
which is connected to the host"::={ alpsCktX25Entry 2}alpsCktX25LCN OBJECT-TYPESYNTAXInteger32(1..4096)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Logical Channel Number being used on the X.25 VC for
this ALPS Circuit."::={ alpsCktX25Entry 3}alpsCktX25HostX121 OBJECT-TYPESYNTAXX121AddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The X.121 address on the host side which the central router uses to
connect to the host"::={ alpsCktX25Entry 4}alpsCktX25RemoteX121 OBJECT-TYPESYNTAXX121AddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"X.121 address of the remote side. Remote here refers to
the side that the ASCUS are connected to and is also
referred to as the remote router."::={ alpsCktX25Entry 5}alpsCktX25DropsVcReset OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets dropped due to the VC being reset. These are
packets that were queued up for transmission on that VC when it
was reset"::={ alpsCktX25Entry 6}-- P1024 (ALC or UTS) Circuit TablealpsCktP1024Table OBJECT-TYPESYNTAXSEQUENCEOF AlpsCktP1024Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of ALC or UTS Alps circuits."::={ alpsCktObjects 3}alpsCktP1024Entry OBJECT-TYPESYNTAX AlpsCktP1024Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details of ALPS Circuits."INDEX{
alpsCktBaseName,
alpsCktP1024DlcType
}::={ alpsCktP1024Table 1}
AlpsCktP1024Entry ::=SEQUENCE{
alpsCktP1024DlcType INTEGER,
alpsCktP1024BackupPeerAddr IpAddress,
alpsCktP1024RetryTimer TimeInterval,
alpsCktP1024IdleTimer TimeInterval,
alpsCktP1024EmtoxX121 X121Address,
alpsCktP1024Ax25LCN Integer32,
alpsCktP1024WinOut Integer32,
alpsCktP1024WinIn Integer32,
alpsCktP1024OutPktSize Integer32,
alpsCktP1024InPktSize Integer32,
alpsCktP1024SvcMsgList Integer32,
alpsCktP1024SvcMsgIntvl TimeTicks,
alpsCktP1024DropsUnkAscu Counter32,
alpsCktP1024RowStatus RowStatus,
alpsCktP1024MatipCloseDelay TimeInterval}alpsCktP1024DlcType OBJECT-TYPESYNTAXINTEGER{alc(3),uts(4)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies what type of circuit this is."::={ alpsCktP1024Entry 1}alpsCktP1024BackupPeerAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This is the IP address of the backup remote peer. This is optional
and hence may not always exist."::={ alpsCktP1024Entry 2}alpsCktP1024RetryTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the interval at which a permanent ALPS circuit
will attempt to reestablish the circuit in case it wasn't
able to come up."::={ alpsCktP1024Entry 3}alpsCktP1024IdleTimer OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If there is no traffic on a dynamic ALPS circuit for this
interval, it will be cleared."::={ alpsCktP1024Entry 4}alpsCktP1024EmtoxX121 OBJECT-TYPESYNTAXX121AddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the X.121 address of the SVC established with
EMTOX host. This field should be set to length zero in
the case of PVCs (AX.25 host)."::={ alpsCktP1024Entry 5}alpsCktP1024Ax25LCN OBJECT-TYPESYNTAXInteger32(0..4096)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the Logical Channel Number being used on the PVC
established with AX.25 host. This field should be set to zero in
the case of SVCs (EMTOX host)."::={ alpsCktP1024Entry 6}alpsCktP1024WinOut OBJECT-TYPESYNTAXInteger32(1..7)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies X.25 transmit Window size on the Logical Channel
Number of this ALPS Circuit."::={ alpsCktP1024Entry 7}alpsCktP1024WinIn OBJECT-TYPESYNTAXInteger32(1..7)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the X.25 receive Window size on the Logical Channel
Number of this ALPS Circuit."::={ alpsCktP1024Entry 8}alpsCktP1024OutPktSize OBJECT-TYPESYNTAXInteger32(128..4096)UNITS"bytes"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the X.25 maxiumum output Packet size on the Logical
Channel Number of this ALPS Circuit. The default output Packet size
for AX.25 is 240 bytes and 128 bytes for EMTOX."::={ alpsCktP1024Entry 9}
alpsCktP1024InPktSize OBJECT-TYPESYNTAXInteger32(128..4096)UNITS"bytes"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies X.25 maximum input Packet size on the Logical Channel
Number of this ALPS Circuit. The default input Packet size for
AX.25 is 240 bytes and 128 bytes for EMTOX."::={ alpsCktP1024Entry 10}alpsCktP1024SvcMsgList OBJECT-TYPESYNTAXInteger32(0..8)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the Service Message List Number to use on this
ALPS Circuit. This allows custom service messages to be sent
for ASCUs on a particular circuit. Service messages are sent out
by the router to the ASCU when abnormal conditions occur, and are
displayed on the terminal. There is a default set of service
messages, usually referred to as List 0. However, it is possible
to configure custom sets of service messages for display,
selectable on a per-circuit basis."DEFVAL{0}::={ alpsCktP1024Entry 11}alpsCktP1024SvcMsgIntvl OBJECT-TYPESYNTAXTimeTicksMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies Service Message Time Interval for the Service
messages to be sent this ALPS Circuit. This controls how
frequently the messages are repeated when an error condition
(e.g. network being down) persists."::={ alpsCktP1024Entry 12}alpsCktP1024DropsUnkAscu OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets that were found to be from an Unknown ASCU
(i.e. an ASCU that had not been configured) and hence were dropped."::={ alpsCktP1024Entry 13}alpsCktP1024RowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsCktP1024Entry 14}alpsCktP1024MatipCloseDelay OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the minumum delay between transmission of a MATIP
Close and the transmission of a MATIP Session Open for
this ALPS circuit."::={ alpsCktP1024Entry 15}-- *********************************************************************
-- * ALPS ASCU Object at Central & Remote routers. This
-- *********************************************************************alpsCktAscuTable OBJECT-TYPE
SYNTAXSEQUENCEOF AlpsCktAscuEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of ASCUs for each ALPS Circuit. This may not include all
ASCUs which have this circuit configured as alpsAscuCktName because
some ASCUs may be rejected by the host while setting up the circuit."::={ alpsCktObjects 4}alpsCktAscuEntry OBJECT-TYPESYNTAX AlpsCktAscuEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details of ASCUs on ASCU Circuits."INDEX{
alpsCktAscuCktName,
alpsCktAscuCktDlcType,
alpsCktAscuA1,
alpsCktAscuA2
}::={ alpsCktAscuTable 1}
AlpsCktAscuEntry ::=SEQUENCE{
alpsCktAscuCktName AlpsCktName,
alpsCktAscuCktDlcType INTEGER,
alpsCktAscuA1 AlpsAscuA1A2Value,
alpsCktAscuA2 AlpsAscuA1A2Value,
alpsCktAscuIfIndex InterfaceIndex,
alpsCktAscuId Integer32,
alpsCktAscuStatus INTEGER}alpsCktAscuCktName OBJECT-TYPESYNTAX AlpsCktName
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"The name of the ALPS circuit which this ASCU is on. The
circuit may be always up (for permanent circuits) or get set up
(dynamic circuits) when there is traffic on one of the ASCUs which
are set up for that circuit."::={ alpsCktAscuEntry 1}alpsCktAscuCktDlcType OBJECT-TYPESYNTAXINTEGER{emtox(1),ax25(2),alc(3),uts(4)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies what type of circuit this is. The X.25 circuit is set up
with the same name as the ALC circuit so we need this
variable to distinguish between the two."::={ alpsCktAscuEntry 2}alpsCktAscuA1 OBJECT-TYPESYNTAX AlpsAscuA1A2Value
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A1 value. This is used along with the alpsCktAscuA2 value to
identify the ASCU within the circuit."::={ alpsCktAscuEntry 3}alpsCktAscuA2 OBJECT-TYPESYNTAX AlpsAscuA1A2Value
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A2 value. This is used along with the alpsCktAscuA1 value to
identify the ASCU within the circuit."::={ alpsCktAscuEntry 4}alpsCktAscuIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the interface the ASCU is on. This field, along with
alpsCktAscuId is provided so that it is possible to correlate this
information with the configured ASCU information in alpsAscuTable"::={ alpsCktAscuEntry 5}alpsCktAscuId OBJECT-TYPESYNTAXInteger32(0..127)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the ASCU Identifier which uniquely
identifies an ASCU on a given interface. This value is
the Interface Address (IA) for ALC and the Remote Identifier
(RID) for UTS. A value of 0 indicates that the ASCU id is either
unavailable or not applicable."::={ alpsCktAscuEntry 6}alpsCktAscuStatus OBJECT-TYPESYNTAXINTEGER{unknown(1),ok(2),reject(3),new(4),pending(5)
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the ASCU status - ASCUs configured on the circuit
can be rejected at the host and would then be marked REJECT. Also,
ASCUs configured after the circuit has been established are not added
dynamically to the circuit but are marked NEW and get added when the
circuit gets established the next time. ASCUs waiting for an accept or
reject response from the host are marked as PENDING. ASCUs that were
accepted by the host are marked OK."::={ alpsCktAscuEntry 7}-- *********************************************************************
-- * ALPS P1024 Interface Object - Interface Table
-- *********************************************************************alpsIfP1024Table OBJECT-TYPESYNTAXSEQUENCEOF AlpsIfP1024Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of interfaces running the P1024B or P1024C protocols"::={ alpsIfObjects 1}alpsIfP1024Entry OBJECT-TYPESYNTAX AlpsIfP1024Entry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Interface Details"INDEX{ ifIndex }::={ alpsIfP1024Table 1}
AlpsIfP1024Entry ::=SEQUENCE{
alpsIfP1024EncapType INTEGER,
alpsIfP1024PollRespTimeout TimeInterval,
alpsIfP1024GATimeout TimeInterval,
alpsIfP1024PollPauseTimeout TimeInterval,
alpsIfP1024MaxErrCnt Integer32,
alpsIfP1024MaxRetrans Integer32,
alpsIfP1024CurrErrCnt Integer32,
alpsIfP1024MinGoodPollResp Integer32,
alpsIfP1024PollingRatio Integer32,
alpsIfP1024NumAscus Gauge32,
alpsIfP1024ServMsgFormat INTEGER,
alpsIfP1024ServMsgStatusChange TruthValue,
alpsIfP1024ServMsgDropTermAddr INTEGER}alpsIfP1024EncapType OBJECT-TYPESYNTAXINTEGER{alc(1),uts(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the encapsulation type for this Serial Interface."::={ alpsIfP1024Entry 1}alpsIfP1024PollRespTimeout OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies the Poll Response Time out value."DEFVAL{500}::={ alpsIfP1024Entry 2}
alpsIfP1024GATimeout OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies the time-out delay between receipt of first character
of an input sequence solicited by a poll and receipt of GA
sequence."DEFVAL{600}::={ alpsIfP1024Entry 3}alpsIfP1024PollPauseTimeout OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies the minimum delay between two poll cycles. Thus
the poll pause interval is counted from the instant when the first
ASCU in the poll list is polled. Note that this is the delay between
two traversals of the entire poll list rather than the interval
between two consecutive polls. The actual delay will
probably be more than the value of this variable."DEFVAL{50}::={ alpsIfP1024Entry 4}alpsIfP1024MaxErrCnt OBJECT-TYPESYNTAXInteger32(0..30)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies a maximum error count for this interface. After
an ASCU link comes up, if it experiences this number of errors the
ASCU link will be shutdown. The default value of 0 results in the
ASCU link never being shutdown."DEFVAL{0}::={ alpsIfP1024Entry 5}alpsIfP1024MaxRetrans OBJECT-TYPESYNTAXInteger32(0..10)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies the maximum number of times an output message will
be retransmitted before it is discarded. This is relevant only
for P1024C (UTS). For ALC, a value of 0 will be returned. Note that
legal values for UTS are 1-10"DEFVAL{3}::={ alpsIfP1024Entry 6}alpsIfP1024CurrErrCnt OBJECT-TYPESYNTAXInteger32(0..30)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the number of errors currently existing for this
ASCU link. When this equals alpsIfP1024MaxErrCnt then the
ASCU link will be shut down, unless alpsIfP1024MaxErrCnt
equals 0 in which case the ascu link is never shut down
due to error thresholds being exceeded"DEFVAL{0}::={ alpsIfP1024Entry 7}alpsIfP1024MinGoodPollResp OBJECT-TYPESYNTAXInteger32(1..30)
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies the number of good Poll Responses to be received
from an ASCU before it can be declared up."DEFVAL{1}::={ alpsIfP1024Entry 8}alpsIfP1024PollingRatio OBJECT-TYPESYNTAXInteger32(1..30)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies how many times ASCUs in UP state are polled before
an ASCU in DOWN state is polled again."DEFVAL{30}::={ alpsIfP1024Entry 9}alpsIfP1024NumAscus OBJECT-TYPESYNTAXGauge32UNITS"Ascus"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the number of ASCUs configured on this Serial Port."DEFVAL{0}::={ alpsIfP1024Entry 10}alpsIfP1024ServMsgFormat OBJECT-TYPESYNTAXINTEGER{sita(1),apollo(2)
}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies the format of the service message sent to an ASCU
on this interface."DEFVAL{ sita }::={ alpsIfP1024Entry 11}alpsIfP1024ServMsgStatusChange OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies whether service messages generated due
to an ALPS circuit status change or an ASCU status change,
will be forwarded to the ASCU."DEFVAL{ true }::={ alpsIfP1024Entry 12}alpsIfP1024ServMsgDropTermAddr OBJECT-TYPESYNTAXINTEGER{msgterm(1),configterm(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Specifies whether the service message will be sent to the same
terminal address of the dropped message or the configured value."DEFVAL{ configterm }::={ alpsIfP1024Entry 13}-- *********************************************************************
-- * ALPS Host Link Interface Object
-- *********************************************************************alpsIfHLinkTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsIfHLinkEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of interfaces running AX.25/EMTOX host link protocols.
These are on the central router"::={ alpsIfObjects 2}alpsIfHLinkEntry OBJECT-TYPESYNTAX AlpsIfHLinkEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details of AX.25/EMTOX host link protocols on an Interface."INDEX{
ifIndex,
alpsIfHLinkHostHld,
alpsIfHLinkNumber
}::={ alpsIfHLinkTable 1}
AlpsIfHLinkEntry ::=SEQUENCE{
alpsIfHLinkHostHld Integer32,
alpsIfHLinkNumber Integer32,
alpsIfHLinkX25ProtocolType INTEGER,
alpsIfHLinkAx25PvcDamp TimeInterval,
alpsIfHLinkEmtoxHostX121 X121Address,
alpsIfHLinkActiveCkts Integer32}alpsIfHLinkHostHld OBJECT-TYPESYNTAXInteger32(1..65535)MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Specifies the HLD of the AX.25/EMTOX host connected on this
Interface. The HLD(High-level descriptor) serves as an
identifier along with the hostlink number and helps correlate the
ALPS circuit to a host link. The hex range is 0x1 to 0xFFFF
which corresponds to 1 ... 65535 in decimal."::={ alpsIfHLinkEntry 1}alpsIfHLinkNumber OBJECT-TYPESYNTAXInteger32(1..255)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the configured Host Link Number on this Serial Interface."::={ alpsIfHLinkEntry 2}alpsIfHLinkX25ProtocolType OBJECT-TYPESYNTAXINTEGER{ax25(1),emtox(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the encapsulation type for this Serial Interface -
AX.25 or EMTOX."::={ alpsIfHLinkEntry 3}alpsIfHLinkAx25PvcDamp OBJECT-TYPESYNTAXTimeIntervalMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The purpose of this object is to handle the link-damping for an
AX.25 host. If the PVC goes inactive (i.e. link goes down, etc...)
for PVCDampValue seconds, then PVC will be destroyed as well as
the associated ALPS circuit."::={ alpsIfHLinkEntry 4}alpsIfHLinkEmtoxHostX121 OBJECT-TYPESYNTAXX121AddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Specfies the X.121 address of this EMTOX host."::={ alpsIfHLinkEntry 5}alpsIfHLinkActiveCkts OBJECT-TYPESYNTAXInteger32(0..4096)UNITS"circuits"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the number of ALPS Ckts established with this host."::={ alpsIfHLinkEntry 6}-- *********************************************************************
-- * Define ALPS ASCU Object
-- *********************************************************************alpsAscuTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsAscuEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of ALPS ASCUs on an interface. This is defined only at
the remote router."::={ alpsAscuObjects 1}alpsAscuEntry OBJECT-TYPESYNTAX AlpsAscuEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Details of ASCU."INDEX{
ifIndex,
alpsAscuId
}::={ alpsAscuTable 1}
AlpsAscuEntry ::=SEQUENCE{
alpsAscuId Integer32,
alpsAscuA1 AlpsAscuA1A2Value,
alpsAscuA2 AlpsAscuA1A2Value,
alpsAscuCktName AlpsCktName,
alpsAscuAlarmsEnabled TruthValue,
alpsAscuRetryOption INTEGER,
alpsAscuMaxMsgLength Integer32,
alpsAscuFwdStatusOption TruthValue,
alpsAscuState INTEGER,
alpsAscuDownReason INTEGER,
alpsAscuOutPackets Counter32,
alpsAscuOutOctets Counter32,
alpsAscuInPackets Counter32,
alpsAscuInOctets Counter32,
alpsAscuDropsGarbledPkts Counter32,
alpsAscuDropsAscuDown Counter32,
alpsAscuDropsAscuDisabled Counter32,
alpsAscuEnabled TruthValue,
alpsAscuRowStatus RowStatus,
alpsAscuAutoReset TruthValue}alpsAscuId OBJECT-TYPESYNTAXInteger32(1..127)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the ASCU Identifier and uniquely
identifies an ASCU on a given interface. This value is
the Interface Address (IA) for ALC and the Remote Identifier
(RID) for UTS. This uniquely identifies an ASCU on a given interface."::={ alpsAscuEntry 1}alpsAscuA1 OBJECT-TYPESYNTAX AlpsAscuA1A2Value
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"A1 value of the ASCU."::={ alpsAscuEntry 2}alpsAscuA2 OBJECT-TYPESYNTAX AlpsAscuA1A2Value
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"A2 value of the ASCU."::={ alpsAscuEntry 3}alpsAscuCktName OBJECT-TYPESYNTAX AlpsCktName
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the ALPS Circuit Name for the circuit that is to be
used for this ASCU's data. Note that all ASCUs on a physical interface
may not use the same ALPS circuit to connect to the central router"::={ alpsAscuEntry 4}alpsAscuAlarmsEnabled OBJECT-TYPESYNTAXTruthValue
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies whether alarms (syslog messages or SNMP traps) will
be generated for this ASCU."DEFVAL{ false }::={ alpsAscuEntry 5}alpsAscuRetryOption OBJECT-TYPESYNTAXINTEGER{resend(1),reenter(2),none(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the retry option for this ASCU. This specifies the
error message to be sent to the terminal when a message
is dropped at the router. The terminal has three choices -
either retransmit the last message (if the terminal can buffer it),
re-enter the last message sent or do nothing. Based on the terminal's
capabilities, one of these three is configured for the ASCU. Note that
this option is the same for all terminals connected to an ASCU
because the ALPS feature does not handle individual terminals"DEFVAL{ none }::={ alpsAscuEntry 6}alpsAscuMaxMsgLength OBJECT-TYPESYNTAXInteger32(1..3840)UNITS"bytes"MAX-ACCESSread-create
STATUScurrentDESCRIPTION"Specifies Maximum length of Input Message that can be received
from this ASCU."DEFVAL{962}::={ alpsAscuEntry 7}alpsAscuFwdStatusOption OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"If this flag is set, status messages received from the ASCU are
forwarded to the host. Otherwise they are discarded. Note that these
are relevant only for P1024C (UTS). For ALC, a value of FALSE will
be returned."DEFVAL{ true }::={ alpsAscuEntry 8}alpsAscuState OBJECT-TYPESYNTAXINTEGER{disabled(1),unknown(2),down(3),up(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the current ASCU Status. ASCUs are initially in
disabled state. They are enabled from the parser
if the operator wants to. This takes them to an UP state from which
they go to a DOWN state if there are too many errors."::={ alpsAscuEntry 9}
alpsAscuDownReason OBJECT-TYPESYNTAXINTEGER{unknown(1),noReason(2),notDown(3),ascuDisabled(4),errorThresholdExceeded(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Reports the Down reason for this ASCU if it is down."DEFVAL{ noReason }::={ alpsAscuEntry 10}alpsAscuOutPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets transmitted to this ASCU."::={ alpsAscuEntry 11}alpsAscuOutOctets OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of octets transmitted to this ASCU."::={ alpsAscuEntry 12}
alpsAscuInPackets OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets received from this ASCU"::={ alpsAscuEntry 13}alpsAscuInOctets OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of octets received from this ASCU."::={ alpsAscuEntry 14}alpsAscuDropsGarbledPkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of packets dropped due to the inability to properly
decode them. Examples of garbled packets include packets with bad
CRCs or bad header information"::={ alpsAscuEntry 15}alpsAscuDropsAscuDown OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of packets dropped because the ASCU had previously
been declared DOWN due to error thresholds being exceeded."::={ alpsAscuEntry 16}alpsAscuDropsAscuDisabled OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of packets dropped because the ASCU had previously
been declared to be in disabled state."::={ alpsAscuEntry 17}alpsAscuEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies whether the ASCU has been enabled or not. After
the ASCU has been configured, it must be explicitly enabled to allow
it to be polled."DEFVAL{ false }::={ alpsAscuEntry 18}alpsAscuRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsAscuEntry 19}alpsAscuAutoReset OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies whether a reset command will be automatically issued
to any non-responsive ALC ASCUs."DEFVAL{ false }::={ alpsAscuEntry 20}-- *********************************************************************
-- * ALPS Service Messages
-- *********************************************************************alpsSvcMsgTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsSvcMsgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of service messages and its associated number. There is
a default list of service messages (list 0) as well as
user-configurable service messages. On a per-circuit basis, the
service message list to use can be selected. The user-configured
service message lists are defined in this table. Note that the
default service messages are not part of this table."::={ alpsGlobalObjects 1}alpsSvcMsgEntry OBJECT-TYPESYNTAX AlpsSvcMsgEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Service Messages configured along with its List number and Service
Message Number in that list."INDEX{
alpsSvcMsgListNum,
alpsSvcMsgNum
}::={ alpsSvcMsgTable 1}
AlpsSvcMsgEntry ::=SEQUENCE{
alpsSvcMsgListNum Integer32,
alpsSvcMsgNum Integer32,
alpsSvcMsg DisplayString,
alpsSvcMsgRowStatus RowStatus}alpsSvcMsgListNum OBJECT-TYPESYNTAXInteger32(1..8)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the Service Msg Number of this Service Msg. A
maximum of 8 Service Message lists can be configured not including
the one for Default/System (when alpsSvcMsgListNum = 0)
Service messages."::={ alpsSvcMsgEntry 1}alpsSvcMsgNum OBJECT-TYPESYNTAXInteger32(1..8)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the Service Msg Number of this Service Msg. A Maximum
of 8 messages can be present."::={ alpsSvcMsgEntry 2}alpsSvcMsg OBJECT-TYPESYNTAXDisplayString(SIZE(1..50))MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the Service Message string ."::={ alpsSvcMsgEntry 3}alpsSvcMsgRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsSvcMsgEntry 4}
-- *********************************************************************
-- * ALPS X.121 to Ip Translation Object - Admin Object
-- *********************************************************************alpsX121ToIpTransTable OBJECT-TYPESYNTAXSEQUENCEOF AlpsX121ToIpTransEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A Translation table between X.121 address and IP address. This
is intended to allow a connection to be established to the
appropriate remote router. The X121 address in the call packet
is used to look up the IP address of the remote peer"::={ alpsGlobalObjects 2}alpsX121ToIpTransEntry OBJECT-TYPESYNTAX AlpsX121ToIpTransEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A mapping table between X.121 address and IP address."INDEX{
ifIndex,
alpsX121
}::={ alpsX121ToIpTransTable 1}
AlpsX121ToIpTransEntry ::=SEQUENCE{
alpsX121 X121Address,
alpsIpAddress IpAddress,
alpsX121ToIpTransRowStatus RowStatus}alpsX121 OBJECT-TYPESYNTAXX121AddressMAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"Specfies the X.121 address of the VC established with
EMTOX host."::={ alpsX121ToIpTransEntry 1}alpsIpAddress OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This is the IP address of the remote peer which maps onto the
X.121 address."::={ alpsX121ToIpTransEntry 2}alpsX121ToIpTransRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create a new row or modify or
delete an existing row in this table."::={ alpsX121ToIpTransEntry 3}-- *********************************************************************
-- * ALPS Notifications at Remote router
-- *********************************************************************ciscoAlpsMIBNotificationPrefix OBJECTIDENTIFIER::={ ciscoAlpsMIB 2}ciscoAlpsMIBNotifications OBJECTIDENTIFIER::={ ciscoAlpsMIBNotificationPrefix 0}alpsPeerStatusChange NOTIFICATION-TYPEOBJECTS{ alpsRemPeerState }STATUSdeprecatedDESCRIPTION"This Notification is generated when there is a change in state
for the peer connection, provided alarms are enabled for
that peer."::={ ciscoAlpsMIBNotifications 1}alpsCktStatusChange NOTIFICATION-TYPEOBJECTS{ alpsCktBaseState }STATUScurrentDESCRIPTION"This Notification has to be generated whenever there is a
state change for the ALPS circuit, provided alarms are
enabled for that circuit"::={ ciscoAlpsMIBNotifications 2}alpsAscuStatusChange NOTIFICATION-TYPEOBJECTS{ alpsAscuState }STATUScurrentDESCRIPTION"This Notification has to be generated whenever there is a
change in ASCU status, provided alarms are enabled for
that ASCU"::={ ciscoAlpsMIBNotifications 3}alpsPeerConnStatusChange NOTIFICATION-TYPEOBJECTS{ alpsRemPeerConnState }STATUScurrentDESCRIPTION"This Notification is generated when there is a change in
state for an ALPS peer connection, provided alarms are
enabled for that peer connection."::={ ciscoAlpsMIBNotifications 4}alpsCktOpenFailure NOTIFICATION-TYPEOBJECTS{ alpsCktBaseDownReason }STATUScurrentDESCRIPTION"This Notification is generated whenever there is an open
failure for the ALPS circuit, provided alarms are enabled
for that circuit"
::={ ciscoAlpsMIBNotifications 5}alpsCktPartialReject NOTIFICATION-TYPEOBJECTS{
alpsCktAscuIfIndex,
alpsCktAscuId
}STATUScurrentDESCRIPTION"This Notification is generated whenever there is an open
confirmation that contains a list of rejected ASCUs for the
ALPS circuit, provided alarms are enabled for that circuit"::={ ciscoAlpsMIBNotifications 6}-- *************************************************************************
-- * Conformance Information
-- *************************************************************************alpsMibConformance OBJECTIDENTIFIER::={ ciscoAlpsMIB 3}alpsMibCompliances OBJECTIDENTIFIER::={ alpsMibConformance 1}alpsMibGroups OBJECTIDENTIFIER::={ alpsMibConformance 2}alpsMibCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for ALPS."MODULE-- this moduleMANDATORY-GROUPS{
alpsPeerGroup,
alpsCktGroup,
alpsIfP1024Group,
alpsIfHostlinkGroup,
alpsAscuGroup,
alpsSvcMsgGroup,
alpsAddrTransGroup,
alpsNotificationGroup
}::={ alpsMibCompliances 1}alpsMibComplianceRev1 MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for ALPS."MODULE-- this moduleMANDATORY-GROUPS{
alpsCktGroup,
alpsIfP1024Group,
alpsIfHostlinkGroup,
alpsAscuGroup,
alpsSvcMsgGroup,
alpsAddrTransGroup,
alpsPeerGroupRev1,
alpsNotificationGroupRev1
}::={ alpsMibCompliances 2}alpsMibComplianceRev2 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for ALPS."MODULE-- this moduleMANDATORY-GROUPS{
alpsCktGroup,
alpsIfP1024GroupRev1,
alpsIfHostlinkGroup,
alpsAscuGroupRev1,
alpsSvcMsgGroup,
alpsAddrTransGroup,
alpsPeerGroupRev1,
alpsNotificationGroupRev2
}::={ alpsMibCompliances 3}alpsPeerGroup OBJECT-GROUPOBJECTS{
alpsPeerLocalIpAddr,
alpsPeerLocalAtpPort,
alpsPeerKeepaliveTimeout,
alpsPeerKeepaliveMaxRetries,
alpsPeerInCallsAcceptFlag,
alpsRemPeerConnType,
alpsRemPeerLocalPort,
alpsRemPeerRemotePort,
alpsRemPeerState,
alpsRemPeerUptime,
alpsRemPeerNumActiveCkts,
alpsRemPeerIdleTimer,
alpsRemPeerAlarmsEnabled,
alpsRemPeerTCPQlen,
alpsRemPeerOutPackets,
alpsRemPeerOutOctets,
alpsRemPeerInPackets,
alpsRemPeerInOctets,
alpsRemPeerDropsGiant,
alpsRemPeerDropsQFull,
alpsRemPeerDropsPeerUnreach,
alpsRemPeerRowStatus
}STATUSdeprecatedDESCRIPTION"A collection of objects providing Peer information"::={ alpsMibGroups 1}alpsCktGroup OBJECT-GROUPOBJECTS{
alpsCktBasePriPeerAddr,
alpsCktBaseAlarmsEnabled,
alpsCktBaseConnType,
alpsCktBaseState,
alpsCktBaseNumActiveAscus,
alpsCktBaseCurrentPeer,
alpsCktBaseLifeTimeTimer,
alpsCktBaseHostLinkNumber,
alpsCktBaseHostLinkType,
alpsCktBaseRemHld,
alpsCktBaseLocalHld,
alpsCktBaseDownReason,
alpsCktBaseOutPackets,
alpsCktBaseOutOctets,
alpsCktBaseInPackets,
alpsCktBaseInOctets,
alpsCktBaseDropsCktDisabled,
alpsCktBaseDropsQOverflow,
alpsCktBaseDropsLifeTimeExpd,
alpsCktBaseEnabled,
alpsCktBaseRowStatus,
alpsCktX25IfIndex,
alpsCktX25LCN,
alpsCktX25HostX121,
alpsCktX25RemoteX121,
alpsCktX25DropsVcReset,
alpsCktP1024BackupPeerAddr,
alpsCktP1024RetryTimer,
alpsCktP1024IdleTimer,
alpsCktP1024EmtoxX121,
alpsCktP1024Ax25LCN,
alpsCktP1024WinOut,
alpsCktP1024WinIn,
alpsCktP1024OutPktSize,
alpsCktP1024InPktSize,
alpsCktP1024SvcMsgList,
alpsCktP1024SvcMsgIntvl,
alpsCktP1024DropsUnkAscu,
alpsCktP1024RowStatus,
alpsCktAscuIfIndex,
alpsCktAscuId,
alpsCktAscuStatus,
alpsCktBaseCurrPeerConnId,
alpsCktP1024MatipCloseDelay
}
STATUScurrentDESCRIPTION"A collection of objects providing Circuit information"::={ alpsMibGroups 2}alpsIfP1024Group OBJECT-GROUPOBJECTS{
alpsIfP1024EncapType,
alpsIfP1024PollRespTimeout,
alpsIfP1024GATimeout,
alpsIfP1024PollPauseTimeout,
alpsIfP1024MaxErrCnt,
alpsIfP1024MaxRetrans,
alpsIfP1024CurrErrCnt,
alpsIfP1024MinGoodPollResp,
alpsIfP1024PollingRatio,
alpsIfP1024NumAscus
}STATUSdeprecatedDESCRIPTION"A collection of objects providing ALC interface information"::={ alpsMibGroups 3}alpsIfHostlinkGroup OBJECT-GROUPOBJECTS{
alpsIfHLinkX25ProtocolType,
alpsIfHLinkAx25PvcDamp,
alpsIfHLinkEmtoxHostX121,
alpsIfHLinkActiveCkts
}STATUScurrentDESCRIPTION"A collection of objects providing Hostlink information"::={ alpsMibGroups 4}alpsAscuGroup OBJECT-GROUPOBJECTS{
alpsAscuA1,
alpsAscuA2,
alpsAscuCktName,
alpsAscuAlarmsEnabled,
alpsAscuRetryOption,
alpsAscuMaxMsgLength,
alpsAscuFwdStatusOption,
alpsAscuState,
alpsAscuDownReason,
alpsAscuOutPackets,
alpsAscuOutOctets,
alpsAscuInPackets,
alpsAscuInOctets,
alpsAscuDropsGarbledPkts,
alpsAscuDropsAscuDown,
alpsAscuDropsAscuDisabled,
alpsAscuEnabled,
alpsAscuRowStatus
}STATUSdeprecatedDESCRIPTION"A collection of objects providing ASCU information"::={ alpsMibGroups 5}alpsSvcMsgGroup OBJECT-GROUPOBJECTS{
alpsSvcMsg,
alpsSvcMsgRowStatus
}STATUScurrentDESCRIPTION"A collection of objects providing Service Message information"::={ alpsMibGroups 6}alpsAddrTransGroup OBJECT-GROUPOBJECTS{
alpsIpAddress,
alpsX121ToIpTransRowStatus
}STATUScurrentDESCRIPTION"A collection of objects providing Address Translation
information."
::={ alpsMibGroups 7}alpsPeerGroupRev1 OBJECT-GROUPOBJECTS{
alpsPeerLocalIpAddr,
alpsPeerLocalAtpPort,
alpsPeerKeepaliveTimeout,
alpsPeerKeepaliveMaxRetries,
alpsPeerInCallsAcceptFlag,
alpsRemPeerCfgActivation,
alpsRemPeerCfgTCPQLen,
alpsRemPeerCfgIdleTimer,
alpsRemPeerCfgNoCircTimer,
alpsRemPeerCfgAlarmsOn,
alpsRemPeerCfgStatIntvl,
alpsRemPeerCfgStatRetry,
alpsRemPeerCfgRowStatus,
alpsRemPeerConnLocalPort,
alpsRemPeerConnForeignPort,
alpsRemPeerConnState,
alpsRemPeerConnProtocol,
alpsRemPeerConnCreation,
alpsRemPeerConnActivation,
alpsRemPeerConnUptime,
alpsRemPeerConnNumActCirc,
alpsRemPeerConnLastTxRx,
alpsRemPeerConnLastRxAny,
alpsRemPeerConnIdleTimer,
alpsRemPeerConnNoCircTimer,
alpsRemPeerConnTCPQLen,
alpsRemPeerConnAlarmsOn,
alpsRemPeerConnStatIntvl,
alpsRemPeerConnStatRetry,
alpsRemPeerConnDownReason,
alpsRemPeerConnOutPackets,
alpsRemPeerConnOutOctets,
alpsRemPeerConnInPackets,
alpsRemPeerConnInOctets,
alpsRemPeerConnDropsGiant,
alpsRemPeerConnDropsQFull,
alpsRemPeerConnDropsUnreach,
alpsRemPeerConnDropsVersion
}STATUScurrentDESCRIPTION"A collection of objects providing peer information."::={ alpsMibGroups 9}alpsIfP1024GroupRev1 OBJECT-GROUPOBJECTS{
alpsIfP1024EncapType,
alpsIfP1024PollRespTimeout,
alpsIfP1024GATimeout,
alpsIfP1024PollPauseTimeout,
alpsIfP1024MaxErrCnt,
alpsIfP1024MaxRetrans,
alpsIfP1024CurrErrCnt,
alpsIfP1024MinGoodPollResp,
alpsIfP1024PollingRatio,
alpsIfP1024NumAscus,
alpsIfP1024ServMsgFormat,
alpsIfP1024ServMsgStatusChange,
alpsIfP1024ServMsgDropTermAddr
}STATUScurrentDESCRIPTION"A collection of objects providing ALC interface information"::={ alpsMibGroups 11}alpsAscuGroupRev1 OBJECT-GROUPOBJECTS{
alpsAscuA1,
alpsAscuA2,
alpsAscuCktName,
alpsAscuAlarmsEnabled,
alpsAscuRetryOption,
alpsAscuMaxMsgLength,
alpsAscuFwdStatusOption,
alpsAscuState,
alpsAscuDownReason,
alpsAscuOutPackets,
alpsAscuOutOctets,
alpsAscuInPackets,
alpsAscuInOctets,
alpsAscuDropsGarbledPkts,
alpsAscuDropsAscuDown,
alpsAscuDropsAscuDisabled,
alpsAscuEnabled,
alpsAscuRowStatus,
alpsAscuAutoReset
}STATUScurrentDESCRIPTION"A collection of objects providing ASCU information"::={ alpsMibGroups 12}alpsNotificationGroup NOTIFICATION-GROUPNOTIFICATIONS{
alpsPeerStatusChange,
alpsCktStatusChange,
alpsAscuStatusChange
}STATUSobsoleteDESCRIPTION"A collection of notifications."::={ alpsMibGroups 8}alpsNotificationGroupRev1 NOTIFICATION-GROUPNOTIFICATIONS{
alpsCktStatusChange,
alpsAscuStatusChange,
alpsPeerConnStatusChange
}STATUSdeprecatedDESCRIPTION
"A collection of notifications."::={ alpsMibGroups 10}alpsNotificationGroupRev2 NOTIFICATION-GROUPNOTIFICATIONS{
alpsCktStatusChange,
alpsAscuStatusChange,
alpsPeerConnStatusChange,
alpsCktOpenFailure,
alpsCktPartialReject
}STATUScurrentDESCRIPTION"A collection of notifications."::={ alpsMibGroups 13}END